eFUSION - FRICTION ROLLOVER CAR WASH
 The eFusion System is designed to effectively clean a vehicle using our unique SparkleSoft foam brushes. SparkleSoft is a strong, hushed and delicate product that glides over the vehicle's surface, enhancing the
gloss and luster, wash after wash. The brushes employ the unique Multi-Axis Coordinated Motion Control to position them.
We've taken the durability factor of the stainless frame and added three (3) soft touch brushes and an optional wheel brush. The system is extremely versatile with performance options such as High Pressure Wash, Hot Wax, Spot Free Rinse and much more. The eFusion is totally programmable to fit your wash needs and to maximize your profits.
 |
| Features:
- Rollover Design Mounted on Railroad Style Gantry Tracks
- Stainless Steel Frame and Gantry
- (3) Three Soft Touch Brushes with SparkleSoft € Multi-Axis Coordinated Motion Control for Brush Positioning
- Foaming Prewash System
- Operator Friendly Totally Programmable Wash Cycles
- SS Instructional Sign - Gantry Mounted
- SS ³Please Wait² and ³Enter Now² Sign
- Automatic Chemical Dosing System
- Independent Delivery Manifold for Presoak and Spot Free
- Manual Controls for Gantry OperationWeb Enabled for Complete Remote Access to System Controls Performance Options:
- Low Pressure/Hot Wax System
- Tri-Color Foaming Conditioner System
-Foaming Tire Cleaner Applicators On-board
- High Pressure Wash - Top and Sides (18GPM or 36 GPM)
- High Pressure Undercarriage Spray System
- Wheel Brush System
- Wheel Brush W/ 3 High Pressure Nozzles
- Presoak Heater System
- Circulating Presoak System
- Winter Wizard Freeze Control System
|
The eFusion electrical requires two electrical connections into the main disconnect switch. The connections go into the Electrical Control Panel and hook up to the Safety Disconnect Switch, located on the upper right. The connection goes into the top of the switch. The 110 VAC hot wire goes into the auxiliary contact on the left side of the switch. The Neutral terminal is located directly left of the auxiliary contact. The amperage requirements for the eFusion are explained under electrical requirements below:
|
Electrical
Required:
- eFusion Main Supply
- 30 Amp, 3ph , 208/230V (17/14 Amp Draw)
- 20Amp, 1 Pole Breaker, 110V
(10 Amp Draw)
Optional High Pressure Wash System
- 1 - 15 Hp / 18 GPM Pump / 1000
PSI (69 Bar)
- 60 Amp, 3 Ph 208/230Volt
(40/37 Amp Draw)
Optional Dual Pump High Pressure Wash System
- 2 - 15 Hp / 18 Gpm Pumps
- 125 Amp, 3 Ph 208/230 Volt
(80/74 Amp Draw)
Water Line Required:
- 1² (26mm) Water - Min. Pressure
40 psi (2.75bar)-Max. 60 psi (4.5 bar)
Max Flow Rate: 12 Gpm
(46 Lpm without HP)
38 Gpm (144 Lpm with HP)
Air Line Required:
- 1/2²(13mm) Air Min. Pressure 80 psi
(5.5 bar)Max. 120 psi (8 bar)
- Air Max Flow Rate:
10 cfm (.283 cubic meter)
|
| |
Dimensions:
- Chemical Dosing
System: 36²wide X 30² high (914mm X 762mm)
- Electrical Control Panel:
24² Wide X 24² High
(610mm X 610mm)
- Gantry: 154² wide X 62² deep X 113²
high (3.91cm wide X 157cm X 2.69m)
- Vehicle Height Clearance: 84²(2.13m)
|
| |
Recommended Bay Dimensions:
(Contact JCC for lesser dimensions)
- Length: 35' 0"(Gantry Track) - (10.67m)
- Width: 16'0" (4.87m)
- Height: 12' (3.66m)
- Min. Door Opening Height: 10' (3.05cm)
|
|
"These specifications subject to change In the interest of product improvement.
Always check specification details." |
|
|
